![wooden go kart frame wooden go kart frame](https://i.ytimg.com/vi/KI-44xdOrT8/maxresdefault.jpg)
30 feet (9.2 m) of 1-inch (2.5 cm) square tubing.Ask lawn mower repair services for spare parts or junked out riding lawnmowers and used 4 cycle engines in the 10 to 15 horsepower range, with horizontal shaft and a drive clutch assembly. Or, you may be able to salvage parts from an old riding lawnmower or a junk go kart found at a yard sale. If you're short on cash, visit a scrap yard and see if you can pick up any low-cost parts. You’re done with this DIY wood Go-Kart.Gather your materials. Pull the rope through the hole with a knot on the bottom preventing the rope from coming out. Drill a hole on each side of the 18″ long steering 2×4. Strap a car seat on top of a 2×6 frame, giving enough room for someone to stand in the back and push the kart. Take a small 1/2″ plywood piece and attach it to the front of the go-kart for the car sign. Make sure to have a washer and nut on both sides of the wheel. Similar to step 4, cut threaded rod to 21″ long and strap it in the back of the frame to 2×6 with plumbing metal straps.
![wooden go kart frame wooden go kart frame](https://blog-imgs-56-origin.fc2.com/i/p/a/ipad864/Wooden-Go-Kart-Plans-With-Pedals-5.jpg)
Strap the rod to the 2×4 with plumbing metal strap using 1 5/8″ wood screws. Go-karts were iconic in the 1980s and 1990s, when many people played and had fun with this vehicle, which was very popular among children and teenagers at. Place it on top of 2×4 aligning it in the center. Using Sawzall with metal blade cut 5/8″ threaded rod to 26″ in length. This is to prevent 2×4 rubbing against the 2×6 when turning the wheels. Place three washers in between 2×4 and the 2×6 frame. Step 3 – Attach the Steering 2×4 to FrameĪttach this 18″ long steering board using a 4″ bolt and nut. The hole is slightly off-center to fit both the rod and the hole on 2×4. Place this board about 8″ from the front edge and drill a 5/8″ hole thru both 2×4 and 2×6 frame. Take another 2×6 board and cut it to 18″ in length. Then, take 2×4 and cut tow pieces to 11″ in length and attach it on both ends using 2 1/2″ wood screws. Take 2×6 and cut two pieces to 58″ in length. See lumber sizes for actual dimensions vs nominal.ĭisclosure: Some of the links on this page as well as links in “tools for this project” and “material list” sections are affiliate links. Note: Lumber dimensions are listed as nominal size. You also might be interested in the other projects I’ve built for kids: Sensory Table, Pucket Game and Triangle Peg Board Game. Draw it on a sheet of copy paper first and think of how lo. Build your seat out of plywood and bolt it to.
WOODEN GO KART FRAME INSTALL
Install your rear axle and wheel assembly. Important points you can combine pipe and square steels to create the frame. The plans I created are very basic and could be easily changed or modified to something else if you have more material to work with. This is the design that we did for the go kart we got. Kids really enjoyed riding it on the sidewalk and in the backyard. My son likes BMWs so I drew a BMW sign with headlights in the front on a piece of plywood. In the back of the car seat, I made the 2×6 platform longer so that someone could stand on it and push against the pavement.
![wooden go kart frame wooden go kart frame](https://siamagazin.com/wp-content/uploads/2019/07/avssav-min-747x420.jpg)
I had some wheels and an old car seat, and that was enough for me to start. I wanted to make a very simple go-kart with stuff that I could find around the house or in a garage.
![wooden go kart frame wooden go kart frame](https://blog-imgs-59-origin.fc2.com/w/o/o/woodwork426/Go-Kart-Plans-Wooden-2.jpg)
Now that my kids are that age, I decided to make a DIY Wood Go-Kart using the extra wheel I had laying around in the garage. Or even take turns with my brother bushing each other down the street. When I was a kid, I always wanted to have some kind of buggy on wheels or a cart that I could have fun rolling down the hill.